NEW

imaFlex 2 Dual 100

CoaXPress-over-Fiber Interface
2 No. of Ports
Processing Product Type
100 Gbps; 200 Gbps Data Bandwidth (p.port; Total)

imaFlex 2 Dual 100 is a programmable CoaXPress-over-Fiber (CoF) frame grabber. It supports two QSFP28 connections, enabling either up to two CoF cameras (4 × 25 Gbps each) or one CoF camera and an optical data forwarding (DF) link to another imaFlex 2 frame grabber. Each connection delivers up to 100 Gbps bandwidth.

The QSFP28 optical connection enables a bandwidth of up to 100 Gbps (4 x 25 Gbps), electromagnetic compatibility, and a virtually unlimited cable length.

Highlights of the programmable CoaXPress frame grabber with two QSFP28 connections:

Image preprocessing for image enhancement and data reduction simplifies system complexity and total cost of ownership (TCO)
Highly flexible Data Forwarding architecture for higher processing speed
10 GB DDR4 RAM
Bus interface: PCIe 3.0 x16
Signal processing: front I/O (8IN/8OUT) and trigger extension (8IN/8OUT)
Active cooling
FPGA services: frame grabber and FPGA programming

The frame grabber is compatible with the racer 2 XL TDI line scan camera with 256 TDI stages, a line rate of up to 500 kHz, and 16k resolution. Together with standard components such as cooling, transceiver module, data and I/O cables, they form a cost-efficient TDI vision system.

Focus applications of the high-performance system
The CoaXPress-over Fiber frame grabber and the entire TDI vision system deliver outstanding results in the following applications: wafer and semiconductor inspection, battery cell inspection, flat panel display inspection, and PCB inspection.

3-year warranty on Basler productsDirect support from local Basler teamsSecure checkout and data protection

Order Number	2200002331
Design-In Sample	now
Manufacturer	Basler
Type	Frame grabber
Product Series	imaFlex Programmable Frame Grabber
Product Type	Processing
Warranty	36 Months

Processor	Xilinx Ultrascale+ KU15P
On-Board Memory	10 GByte DDR4-RAM
I/O Module Interfaces (Trigger and Sync)	Front GPIO: up to 4 differential signals in, up to 8 single-ended signals in (depends on configuration), 8 TTL outputs Trigger-/GPIO-Extension (for Opto Trigger or TTL Trigger)
Acquisition Card Features	VisualApplets compatible

Interface	CoaXPress-over-Fiber
Configurations	One (1) CoF 425G & One (1) 425G DF or Two (2) CoF 4*25G
Connectors	2 x QSFP28
Cable Length	0 - 100 meters
Camera Support	CoF 4x25G camera
Sensor Type	Grayscale sensor
Bit Depth	8-16-bit (grayscale)
Data Bandwidth	2 x 100 Gbit/s (9,697 MB/s)
Data Bandwidth (p.port; Total)	100 Gbps; 200 Gbps
Test Environment	Camera Simulator
No. of Ports	2

PC Bus Interface	PCIe x16 Gen3.0
PC Bus Interface Performance	15,752 MB/s (theoretical), 13,040 MB/s (typical/max.)

Trigger Board GPIO Interfaces	Box connector (34-pin)
On-board GPIO interface	One 34-pin flat cable connector onboard: 8 input signals and 8 output signals with open-drain optionally as 4 opto-coupled inputs (4,5V - 28V), optional 2 opto-coupled differential inputs (RS422); 4 opto-coupled outputs (4,5V - 28V)
On-board Front GPIO Interface	4 differential input signals up to 8 single-ended input signals; 8 TTL output signals; configurable by software in the applet; max. voltage of the input signals between 4,5V and 25V
GPIO Synchronisation and Control	Configurable Trigger System supporting various trigger modes (grabber controlled, external trigger, gated, software trigger) and shaft encoder functionality with backward compensation, Multi-Camera-Synchronization
GPIO Interface Summary	16 in/16 out (max.), TTL or opto-coupled; differential or single-ended signals (configuration dependent)

imaFlex 2 Dual 100

General Information

Device Features

Camera Interface

Host PC Interface

Controls and General-Purpose I/Os

Physical and Environmental Information

Software

Manufacturer

Conformity

Documentation

Features

Easy Handling

Image Quality Optimization

Process Control

Speed Increase

Suitable Products

Product successfully added to cart

Dimensions	PCIe Standard height, three-quarters length card: 239 mm length x 111.15 mm height
Weight	394 g
Power Consumption / Power Source	Typ. 45W@12V, excluding camera and I/O power output
Operating Temperature	0 - 50 °C (32 - 122 °F)
Storage Temperature	-50 - 80 °C (-58 °F - 176 °F)
Relative Humidity (operating, storage)	5 - 90 % non-condensing (operating), 0 - 95 % (storage)
MTBF	172,174 h
Compliances	CE FCC KC REACH RoHS UKCA WEEE

Software Drivers	Windows 11 / 10 (64-Bit)
Software Tools	Device Drivers Documentation microDiagnostics (Analysis and service tool) microDisplay X (Acquisition control and viewer) Calibration Tool (incl. python source)
Software API	Framegrabber SDK
FPGA Programming	VisualApplets
MV Software Compatibility	GenTL-based MV-Software

Image Selector	Use a module to select the images you want to keep, process, or forward.
Invert	Invert the pixel values of your images to enable more efficient image processing.
Mirroring	Mirror the images in different directions to achieve your ideal hardware setup.

LUT	By creating a custom lookup table (LUT), you can replace the pixel values of your images with values you define yourself.
Offset/Gain/Gamma Correction	Change the brightness values of your images for efficient image processing and optimized monitor display.

ROI	Limit the image flow to relevant sensor areas to ensure efficient image processing.
VisualApplets Compliance	Use the preprocessing capabilities of VisualApplets to reduce the load on your application, reduce image data, improve image quality, or speed up image processing. This feature is a property of the programmable frame grabber.